行业资讯
冷再生机减速机齿轮油的更换方式
来源：https://www.sddhfjx.com/ 日期：2023-04-03
准备事项：
Preparation:
1、场地:要求无尘硬化路面，面积应在200平方米左右，尽量是库房，但要有足够25吨的吊车的工作高度和半径。
1. Site: Dust free and hardened pavement is required, with an area of about 200 square meters. It should be a warehouse as much as possible, but it should have a working height and radius sufficient for a 25 ton crane.
2、设施：25吨吊车一台（20吨也可以）。
2. Facilities: One 25 ton crane (20 tons is also acceptable).
3、配件：进口美孚齿轮油9升、卫生纸10卷、塑料带20个、废油桶2个、紧固胶262/340一支、密封胶587一支、黄油一袋，细线绳20米、12*45的带母螺栓30套、4*30开口销10个。
3. Accessories: 9 liters of imported Mobil gear oil, 10 rolls of toilet paper, 20 plastic belts, 2 waste oil drums, a piece of fastening glue 262/340, a piece of sealant 587, a bag of butter, 20 meters of string, 30 sets of 12 * 45 bolts with nuts, and 10 4 * 30 cotter pins.
4、工具：10、16、18、19、21、22、24、30套筒和扳手至少一套、快速扳手及长、短接杆各一、加力杆一根、30的轮胎扳手、10毫米的内六角扳手、55的活口扳手两把、小号活口扳手一把、小号的老虎钳一把、手钳一把、一字螺丝刀一把、大小锤头各一、撬棍两根，配备气动扳手和气泵，能提高工作效率。
4. Tools: At least one set of 10, 16, 18, 19, 21, 22, 24, 30 sockets and wrenches, one quick wrench and one long and short extension rod each, one force bar, 30 tire wrench, 10 mm hexagonal wrench, two 55 adjustable wrenches, one small adjustable wrench, one small vise, one hand wrench, one slotted screwdriver, one large and small hammer head each, two crowbars, equipped with pneumatic wrench and air pump, can improve work efficiency.
（冷再生机租赁减速机油位及减速机油的检查：先切断电源，等待减速机冷却后打开放油螺塞，检查油是否充满，避免漏油，取油样，检查油色泽及粘度指数，如果油明显浑浊，建议尽快更换。新减速机使用后（500-1000）小时更换新油（将内部污油冲干净），其后每使用1500小时需要更换油一次，但是在使用过程中，仍需要检查油的质量，若油有老化、变质情况要随时更换。）
(Inspection of the oil level and speed reducer oil for leasing a cold regeneration machine: First cut off the power supply, wait for the speed reducer to cool down, open the oil drain plug, check whether the oil is full to avoid oil leakage, take an oil sample, check the oil color and viscosity index, and if the oil is obviously turbid, it is recommended to replace it as soon as possible. After using a new speed reducer, replace it with a new oil (flush the internal dirty oil) within (500-1000) hours, and then replace the oil every 1500 hours of use, "However, during use, it is still necessary to check the quality of the oil and replace it at any time if there is aging or deterioration."
此外冷再生机在施工过程中会有大量的灰尘落到再生机的表面，包括施工中沾污的油迹等污染物，影响外观事小，更为严重的是成为腐蚀的诱发因素。冷再生机在施工过程中会有大量的灰尘落到再生机的表面，包括施工中沾污的油迹等污染物，影响外观事小，更为严重的是成为腐蚀的诱发因素。更多事项就来我们网站https://www.sddhfjx.com咨询吧！
In addition, during the construction process of the cold regenerator, a large amount of dust will fall onto the surface of the regenerator, including pollutants such as oil stains that are contaminated during construction, which have a small impact on the appearance, and more importantly, become an inducing factor for corrosion. During the construction process of a cold regenerator, a large amount of dust will fall onto the surface of the regenerator, including pollutants such as oil stains that are contaminated during construction, which have a small impact on the appearance and, more seriously, become an inducing factor for corrosion. For more information, please visit our website https://www.sddhfjx.com Consult!
公司地址：济南市槐荫区经一路273号群盛华城2号楼1-404
公司名称：山东途畅路桥工程有限公司 
备案号：