行业资讯
泥路面冷再生机怎么去操作？
来源：https://www.sddhfjx.com/ 日期：2021-09-28
以冷再生租赁机为例，它配备了如下先进的智能控制系统：
Taking the cold regeneration rental machine as an example, it is equipped with the following advanced intelligent control system:
1. 动力采用康明斯发动机，功率为500HP。
1. Cummins engine is adopted as the power, and the power is 500hp.
2. 作业转子驱动采用机械（皮带）传动，动力传动比液压传动效率提高25%，皮带传动使冲击载荷免于传到发动机上，根据不同的负载情况通过置换皮带轮可得到不同的转速。
2. The operating rotor is driven by mechanical (belt) transmission. The power transmission efficiency is 25% higher than that of hydraulic transmission. Belt transmission prevents the impact load from being transmitted to the engine. Different speeds can be obtained by replacing the belt pulley according to different load conditions.
3. 转向方式有前轮转向、蟹型转向、后轮转向、全轮转向，因此具有良好的机动性能。
3. The steering modes include front wheel steering, crab steering, rear wheel steering and all wheel steering, so it has good maneuverability.
4. 本机具有功率自动分配功能，当铣拌阻力增加发动机转速下降时，微控器能够调节行走系统的功率，补偿铣拌系统的功率，保证该机在最大效率和最大生产率状态下工作。
4. The machine has the function of automatic power distribution. When the milling and mixing resistance increases and the engine speed decreases, the microcontroller can adjust the power of the walking system and compensate the power of the milling and mixing system to ensure that the machine works under the state of maximum efficiency and productivity.
5. 液体喷洒计量系统，微控器能够根据行走速度铣拌深度及铣拌宽度自动调节喷洒量的大小，实现喷洒量的精确计量控制，满足旧沥青路面的再生要求。
5. For the liquid spraying metering system, the micro controller can automatically adjust the spraying amount according to the walking speed, milling depth and milling width, so as to realize the accurate metering control of the spraying amount and meet the regeneration requirements of the old asphalt pavement.
6. 装备MOBA铣刨机找平系统，MOBA铣刨机找平系统专为控制铣刨机工作时的铣刨深度设计，通过传感器对铣刨鼓相对于铣刨机机身位置的距离变化进行检测，将变化量转化为电信号传输给控制器，再由控制器自动对铣刨鼓进行调整，从而实现对铣刨深度的自动控制。
6. The MoBa milling machine leveling system is equipped. The MoBa milling machine leveling system is specially designed to control the milling depth when the milling machine is working. The distance change of the milling drum relative to the body position of the milling machine is detected through the sensor, the change is converted into an electrical signal and transmitted to the controller, and then the controller automatically adjusts the milling drum, so as to realize the automatic control of the milling depth.
7. 本机具有GPS远程故障诊断系统，使用GPS远程监控系统，可实现设备的全球定位、设备工作信息监控、故障诊断、远程维护和报警，以及锁车、防盗等功能。通过嵌入式计算机技术和移动通信技术搭建的服务管理平台，能通过网络终端实时远程监控，实施远程管理。
7. The machine has a GPS remote fault diagnosis system. Using the GPS remote monitoring system, it can realize the functions of equipment global positioning, equipment work information monitoring, fault diagnosis, remote maintenance and alarm, as well as vehicle locking and anti-theft. The service management platform built by embedded computer technology and mobile communication technology can realize real-time remote monitoring and remote management through network terminal.
（1）能够远程观测到设备所处的地理位置以及现场施工轨迹及观测到其施工区范围。
(1) It can remotely observe the geographical location of the equipment, the on-site construction track and the scope of its construction area.
（2）能够进行车辆发动机各项参数、工作状态、油压的运行情况和运行异常报警预告的实时信息状态查。
(2) It can check the real-time information status of vehicle engine parameters, working status, oil pressure operation and abnormal operation alarm.
公司地址：济南市槐荫区经一路273号群盛华城2号楼1-404
公司名称：山东途畅路桥工程有限公司 
备案号：