公司新闻
冷再生机租赁时打滑的原因及方法？
来源：https://www.sddhfjx.com/ 日期：2020-09-24
求租冷再生机时打滑的原因及方法和优点有哪些，接下来小编将带大家一起来了解下，希望以下的介绍可以让大家更好的了解在运用时会出现的一些问题，希望对大家有所帮助。客户在冷再生机租赁使用过程中，不可避免地会出现消耗和磨损，其中，冷再生机输送带特别容易出现问题，运行时间长，可能出现打滑现象，影响工作效率。让冷再生机租赁厂家带我们一起来分析下打滑的原因和解决办法。
I hope that you can understand the advantages and disadvantages of the recycling machine when you use it. In the process of leasing and using the cold regenerator, the customers will inevitably suffer from consumption and wear. Among them, the conveyor belt of the cold regenerator is particularly prone to problems, and the running time is long, which may cause slipping phenomenon, affecting the work efficiency. Let the cold recycling machine rental manufacturers to take us together to analyze the causes of slip and solutions.
1、初始张力太小。
1. The initial tension is too small.
输送带离开滚筒的张力不够，会引起皮带打滑。一般来说，这种情况是在启动时发生的。如果你想解决它，你必须调整张力装置和增加初始张力。
The tension of the conveyor belt leaving the drum is not enough, which will cause the belt to slip. In general, this happens at startup. If you want to solve it, you have to adjust the tension device and increase the initial tension.
2、摩擦力是不够的。
2. Friction is not enough.
传动滚筒与输送带之间的摩擦力不足以引起滑动。造成这种现象的主要原因是输送带上的水或环境潮湿。解决方法：在气缸中加入一些松香末。注意不要用手而应用鼓风设备吹入，以免发生事故。
The friction between the drive drum and the conveyor belt is not enough to cause sliding. The main reason for this phenomenon is the water on the conveyor belt or the environment is humid. Solution: add some rosin powder into the cylinder. Pay attention not to blow in by hand with blowing equipment to avoid accidents.
3、轴承损坏
3. Bearing damage
尾部滚子轴承损坏或不旋转。造成损坏的原因是机器尾部太浮、太沉，不能及时修理和更换损坏的或不灵活的部件，这导致由打滑引起的阻力增加。
The tail roller bearing is damaged or does not rotate. The reason for the damage is that the tail of the machine is too floating and heavy to repair and replace the damaged or inflexible parts in time, which leads to the increase of resistance caused by slipping.
4、起步太快。
4. Starting too fast.
起动速度太快，不能打滑。这个时候可慢速启动。如果使用鼠笼电机，则可以移动两次，然后被激活，还可以有效地克服打滑现象。
The starting speed is too fast to slip. You can start it slowly at this time. If the squirrel cage motor is used, it can be moved twice and then activated, and the slip phenomenon can be effectively overcome.
5、输送带负荷过大。
5. The belt is overloaded.
输送带的负荷过大，超过电机能力也会打滑。打滑的优点是保护电机。否则，电动机将长期燃烧。但对于运行来说则是打滑事故。
If the load of the conveyor belt is too large, it will slip if it exceeds the capacity of the motor. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is a slip accident.
以上是关于冷再生机租赁时打滑的原因及方法的介绍，希望对大家有所帮助，感谢您的阅读，如想了解更多内容欢迎点击我们的http://www.sddhfjx.com官网。
The above is about the reason and method of cold regenerator slipping when leasing. I hope it will help you. Thank you for your reading. If you want to know more, please click our http://www.sddhfjx.com Official website.
公司地址：济南市槐荫区经一路273号群盛华城2号楼1-404
公司名称：山东途畅路桥工程有限公司 
备案号：