公司新闻
冷再生机租赁工作中遇到输送带打滑问题该怎么办？
来源：https://www.sddhfjx.com/ 日期：2020-08-24
冷再生机租赁进行施工阶段，在连续使用过程中，不可避免地会有消耗和磨损。其中，铣床的输送带特别容易出现问题，运行时间长，可能出现打滑现象，影响工作效率。接下来，让我们分析滑动的原因及其解决方案。
In the construction stage of leasing cold regenerator, in the continuous use process, there will inevitably be consumption and wear. Among them, the conveyor belt of milling machine is particularly prone to problems, long running time, may appear sliding phenomenon, affecting work efficiency. Next, let's analyze the causes of the slippage and the solutions.
1.初始张力太小。
1. The initial tension is too small.
输送带离开滚筒的地方张力不足会导致输送带打滑。一般来说，这种情况发生在启动时，如果你想解决它，你需要调整张力装置和增加初始张力。
Insufficient tension where the belt leaves the drum will cause the belt to slip. Generally speaking, this happens at startup, and if you want to solve it, you need to adjust the tension device and increase the initial tension.
2.摩擦不足
2. Insufficient friction
传动滚筒和传送带之间的摩擦不足会导致打滑。造成这种现象的主要原因是输送带上有水或潮湿的环境。解决方法：在鼓中加入一些松香粉。小心不要用手放进去，要用爆破器材吹进去，以免发生意外。
Insufficient friction between the drive drum and the conveyor belt can cause slippage. The main reason for this phenomenon is that there is water or humid environment on the conveyor belt. Solution: add some rosin powder to the drum. Be careful not to put it in by hand, but to blow it in with blasting equipment to avoid accidents.
3.轴承损坏
3. The bearing is damaged
后滚筒轴承损坏不转或上下滚筒轴承不转。造成损坏的原因是机器尾部太浮、下沉，损坏或不灵活的部件没有及时修理和更换，造成阻力增大、打滑。
The rear roller bearing does not rotate or the upper and lower roller bearing does not rotate. The cause of damage is that the tail of the machine is too floating and sinking, and the damaged or inflexible parts are not repaired and replaced in time, resulting in increased resistance and slipping.
4.启动速度太快
4. The starting speed is too fast
如果起动速度太快，也可能发生打滑。此时可以缓慢启动。如果采用鼠笼式电动机，启动前可激活两次，并能有效克服打滑现象。
If the starting speed is too fast, it may also slip. It can be started slowly at this time. If the squirrel cage motor is used, it can be activated twice before starting and can effectively overcome the phenomenon of slipping.
5.铣床租赁输送带超载
5. The conveyor belt of the milling machine is overloaded
如果输送带的负荷过大，超过电机的能力就会打滑。此时，打滑的好处是保护电机。否则，电机会在长时间后烧毁。但对于操作来说，这是一次滑倒事故。
If the belt is overloaded, it will slip if it exceeds the capacity of the motor. At this time, the advantage of slipping is to protect the motor. Otherwise, the motor will burn out after a long time. But for operation, it was a slip accident.
以上是关于冷再生机租赁工作中遇到输送带打滑问题的分析，希望对大家有所帮助，如您想要了解更多信息欢迎点击http://www.sddhfjx.com。
The above is about the cold recycling machine rental work encountered in the conveyor belt slip problem analysis, hope to help you, if you want to know more information, welcome to click http://www.sddhfjx.com 。
公司地址：济南市槐荫区经一路273号群盛华城2号楼1-404
公司名称：山东途畅路桥工程有限公司 
备案号：